VELAR

Home / Safety & care guide

A pressure cooker is safe when you understand it.

Most fear of pressure cookers comes from not knowing what the whistle, the valve and the gasket are each doing. Here is all of it, in plain terms.

Cutaway diagram of a Velar cooker lid showing the vent weight, the Gasket Release System valve and the gasket.

How it works

Water boils at 100 °C in an open pot. Seal the pot and the steam has nowhere to go, so pressure climbs and the boiling point rises to about 120 °C. Food cooks faster because it is hotter, not because it is squeezed.

Three parts keep that pressure in a safe range:

  • The gasket: a silicone ring that seals the lid to the body. It also releases on its own if pressure ever climbs past the valves.
  • The vent weight: a CNC-machined stainless steel piece that lifts and whistles at 1 kg/cm². It sets the working pressure and bleeds off anything above it. That whistle is the cooker working correctly.
  • The Gasket Release System (GRS): a lead-free backup valve in the lid that vents on its own between 1.25 and 2.5 kg/cm² if the vent weight ever fails to release. If this one fires, stop and clean the cooker before the next use.

All three are on both the Regular and the Handi, and all three are user-replaceable with parts your local stockist keeps on the shelf.

Reading the whistle

A whistle is one full release of steam through the vent weight. Count from the first one, then start timing or turn the flame down.

On a medium flame, 5 L cooker, from a cold start
DishWhistlesThen
Toor / moong dal3–4Flame off, natural release
Rice2Flame off, natural release
Rajma / chhole (soaked)5–6Low flame 10 min, then off
Chana / kabuli (soaked)6–7Low flame 12 min, then off
Whole potatoes3Flame off, quick release safe
Chicken curry4–5Flame off, natural release
Idli / steamed (separator)0Vent weight off, 10–12 min steam
Natural release vs quick release. Natural release means leaving the cooker alone until the weight drops by itself and the lid turns freely, usually 8 to 15 minutes. Quick release means lifting the weight with a spoon to let the steam out fast. Use natural release for pulses and meat so they finish cooking; quick release only for vegetables you do not want to overcook, and always with the vent pointed away from you and from the wall cabinet.

Before every cook

Ten seconds of checks. Do them while the water is still cold.

Look through the vent

Hold the lid to the light and check the vent-weight pipe is clear. A trapped grain of rice or a bit of dal skin is the usual cause of a cooker that will not whistle.

Press the GRS valve

Push the Gasket Release System plug in the lid with a fingertip. It should feel firm and spring back. If it is soft, sticky or cracked, change it before cooking.

Check the gasket seats flush

Run a finger round the ring. It should sit evenly under the rim with no twist and no gap. A gasket that has gone hard or shiny will not hold pressure.

Do not overfill

Liquids and dal to two-thirds. Anything that foams or expands (rice, split pulses) to half. The space above the food is what the steam needs.

Close on the marks

Line the lid arrow to the body arrow before you turn. If it fights you, stop. A forced lid usually means the gasket is pinched.

Always some liquid

At least one cup of water or gravy in the pot, every time. A pressure cooker cannot run dry. The steam is the whole mechanism.

Replacing the gasket

A one-minute job with no tools. A ₹40 part, stocked at every Velar shop, both sizes, both models.

  1. Let it cool, then pull the old ring out

    Only on a cold cooker. Work the old gasket inward and away from the lid rim, a bit at a time, until it comes free. It should not need cutting.

  2. Clean the groove and check the rim

    Wipe the channel the gasket sits in. Look along the lid rim for dents or bright scrape marks. A knocked rim will not seal on any gasket, and that lid needs replacing.

  3. Seat the new one at four points first

    Press the new gasket under the rim at twelve, three, six and nine o'clock, then push the rest in between them. Working round in one direction stretches it unevenly.

  4. Confirm it sits flush, then water-test

    Run a fingertip all the way round. The ring should be level with no bulge. Cook two cups of plain water to one whistle. If steam escapes from the rim, open, re-seat, and test again.

The gasket is the only part that wears on a predictable schedule. A tiffin kitchen running the cooker three times a day will change it every few months; a household cooking dinner once a day gets a year or more. Keep the spare that came in the box, and buy the next one before the current one hardens.

Service intervals

Nothing here needs a service centre. Every part is sold over the counter.

PartReplaceReplace sooner if
Silicone gasket Every 12–18 months of home use, or ~1,500 cooks It has gone hard, shiny, sticky, cracked, or smells burnt; or steam leaks from the rim
Gasket Release System (GRS) Every 2 years It has discoloured, gone soft, or has ever blown during a cook
Vent weight Inspect yearly, rarely needs replacing It is pitted, the pipe is scaled, or it sits crooked and hisses continuously instead of whistling in bursts
Handle set Only when loose or cracked A rivet has worked loose, or the bakelite is split. A loose handle on a full cooker is the one to act on immediately

Cleaning

The body is tough. The lid parts want a gentler hand.

Do

  • Wash the body with dish soap and a soft scrubber. Both the Regular and the Handi are stainless steel, so the body can go in the dishwasher. The mirror finish just stays brighter for longer with hand washing.
  • Take the gasket out after each cook, rinse it, dry it, and store it in the lid rather than stretched over it.
  • Clear the vent pipe under running water and hold it to the light to check it is open.
  • Remove hard-water scale with a 1:3 vinegar-and-water soak, then rinse well.

Don't

  • Steel wool or scouring powder on the mirror-polished body. It dulls the finish and can scratch the surface.
  • Soaking the lid overnight with the gasket, valve and weight fitted. Water sits in the fittings and corrodes them.
  • Oil or grease on the gasket to "help it seal". It swells the silicone and shortens its life.
  • Putting the lid away wet. Dry the underside and the vent before it goes in the cupboard.

Never do this

Short list. Every item on it is how a pressure cooker actually causes harm.

  • Never force a lid that will not open. If it will not turn, there is still pressure inside. Run the base under a cold tap for a minute, or lift the vent weight and wait. It will open when it is safe to.
  • Never cook with a blocked vent. If no steam comes and no whistle builds after several minutes on a good flame, turn off the heat, release pressure, and clear the pipe before trying again.
  • Never substitute parts from another brand. A vent weight or safety valve sets the pressure this cooker was built and tested for. A heavier weight from another make raises it past the design limit.
  • Never deep-fry in it or use it in the oven. It is built for steam and moist heat. Dry heat past the boiling point of your liquid damages the base and the fittings.
  • Never leave it unattended on a high flame. Bring it to pressure on medium, drop the flame once it whistles, and stay in the kitchen.
  • Never point a quick release at yourself, a child, or a wall cabinet. The steam is at 120 °C. Vent it toward open space.

If the Gasket Release System has ever fired during a cook, take the cooker to your stockist for a check before using it again. It is covered under warranty.

If something is wrong

The four problems people actually call us about.

Steam is escaping from around the rim, not the vent

The gasket is not sealing. Nine times out of ten it has hardened and needs replacing. Before that: let the cooker cool, take the gasket out, check it is not twisted or pinched, wipe the lid groove and rim clean, and re-seat it at four points. If it still leaks with a fresh gasket, check the lid rim for a dent. A knocked rim needs a new lid, which is covered for five years.

No pressure is building and there is no whistle

Almost always a blocked vent pipe. Turn off the heat, release any pressure, take the vent weight off, and clear the pipe under running water. Check the weight itself is not clogged. Also confirm there is enough liquid in the pot (at least one cup) and that the lid is fully closed on the marks.

The cooker hisses continuously instead of whistling in bursts

The vent weight is sitting crooked or is worn, so it is leaking steam instead of holding and releasing. Turn the flame down. If the hiss settles into proper whistles, the flame was simply too high. If it hisses even on a low flame, replace the vent weight.

The lid is stuck and will not open after cooking

There is still pressure inside, or a vacuum has formed as it cooled. Never force it. Lift the vent weight with a spoon to check for remaining steam, then run the base under a cold tap for a minute to break the vacuum. It will open freely once the pressure has equalised.

The base has a white film or rainbow tint

Cosmetic, not a fault. The white film is hard-water scale. Soak in one part vinegar to three parts water and rinse. The rainbow tint on stainless is heat discolouration and does not affect the steel. Neither is covered or needs to be.

Still stuck? Message us on WhatsApp with a photo and the batch number stamped under the base. Monday to Saturday, 10am to 7pm. Open WhatsApp